From 0ecee8326608a070b476a757cf517d0f50b5ca07 Mon Sep 17 00:00:00 2001 From: Paul Fertser <fercerpav@gmail.com> Date: Mon, 23 Jan 2017 00:46:51 +0300 Subject: [PATCH] Restore normal development cycle Signed-off-by: Paul Fertser <fercerpav@gmail.com> --- NEWS | 124 +---------------------------------------- NEWS-0.10.0 | 155 +++++++++++++++++++++++++++++++++++++++++++++++++++ configure.ac | 2 +- 3 files changed, 157 insertions(+), 124 deletions(-) create mode 100644 NEWS-0.10.0 diff --git a/NEWS b/NEWS index e3b1e2565..9df165004 100644 --- a/NEWS +++ b/NEWS @@ -2,149 +2,27 @@ This file includes highlights of the changes made in the OpenOCD source archive release. JTAG Layer: - * New driver for J-Link adapters based on libjaylink - (including support for FPGA configuration, SWO and EMUCOM) - * FTDI improvements to work at 30MHz clock - * BCM2835 native driver SWD and Raspberry Pi2 support - * BCM2835 is set to 4ma drive, slow slew rate - * ixo-usb-jtag (emulation of an Altera Bus Blaster I on - Cypress FX2 IC) support - * JTAG pass-through mode for CMSIS-DAP (including support for - FPGA configuration) - * OpenJTAG support for Cypress CY7C65215 - * connect_assert_srst support for SWD - * Xilinx Virtex-II Series7 bitstream loading support - * Use JEP106 data to decode IDs - * Deprecated "ft2232" driver removed (use "ftdi" instead) - * GPL-incompatible FTDI D2XX library support dropped (Presto, - OpenJTAG and USB-Blaster I are using libftdi only now) - * ZY1000 support dropped (unmaintained since long) - * oocd_trace support dropped Boundary Scan: Target Layer: - * ARMv7-A, Cortex-M, Cortex-A/R important fixes and - improvements (allowing e.g. simultaneous debugging of A8 and - M3 cores, JTAG WAIT support etc.) - * ARM Cortex-A,R allow interrupt disable during single-step - (maskisr command) - * Semihosting support for ARMv7-A - * ARM Cortex-M7 support - * Intel Quark mcu D2000 support - * Freescale LS102x SAP support - * ThreadX RTOS support on ARM926E-JS - * Cortex-M RTOS stack alignment fixes - * FreeRTOS FPU support - * uC/OS-III RTOS support - * bridging semihosting to GDB's File-I/O support - * -defer-examine option added to target create command - * verify_image_checksum command added Flash Layer: - * Atmel SAM4S, SAM4N, SAM4C support - * Atmel SAMV, SAMS, SAME (Cortex-M7) support - * Atmel AT91SAMD handle reset run/halt in DSU, other fixes - * Atmel AT91SAML21, SAML22, SAMC20/SAMC21, SAMD09 support - * ST STM32F4x support - * ST STM32F74x/76x/77x, STM32L4 support - * ST STM32L0 categories 1, 2 and 5 support - * Kinetis K02, K21, K22, K24, K26, K63, K64, K66 support - * Kinetis KE, KVx, K8x families support - * Kinetis FlexNVM handling - * Kinetis flash protection, security, mass_erase improvements - * Infineon XMC4xxx family support - * Infineon XMC1000 flash driver - * Energy Micro EFM32 Happy Gecko support - * Energy Micro EFM32 debug interface lock support - * Analog Devices ADuCM360 support - * Unified Nuvoton NuMicro flash driver - * NIIET K1921VK01T (Cortex-M4) support - * Nordic Semiconductor nRF51 improvements - * Spansion FM4 flash (including MB9BFx64/x65, S6E2DH) driver - * Ambiq Micro Apollo flash driver - * PIC32MX new device IDs, 17x/27x flash support - * read_bank() and verify_bank() NOR flash internal API to - allow reading (and verifying) non-memory-mapped devices - * JTAGSPI driver to access SPI NOR flashes via a trivial - FPGA proxy - * Milandr read/verify for Info memory support - * Various discrete SPI NOR flashes support - * CFI 16-bit flash reversed endianness support Board, Target, and Interface Configuration Scripts: - * Digilent JTAG-HS2, JTAG-HS3 interfaces configs - * FTDI UM232H module as JTAG interface config - * 100ask's OpenJTAG interface config - * MBFTDI interface config - * XDS100v3 interface config - * Freescale Vybrid VF6xx target config - * EmCraft VF6 SOM and baseboard configs - * Freescale SabreSD board config - * Freescale VF65GS10 tower board config - * Pipistrello Xilinx Spartan6 LX45 FPGA board config - * miniSpartan6+ board config - * Xilinx Kintex7 Development board config - * Parallella-I board config - * Digilent Atlys and Analog Discovery board configs - * Numato Opsis board config - * Xilinx Spartan 6 FPGA "Device DNA" reading support - * Altera 10M50 FPGA (MAX10 family) target config - * Altera EPM240 CPLD (MAXII family) target config - * Marsohod2, Marsohod3 FPGA, Marsohod CPLD boards configs - * Novena's integrated FPGA board config - * XMOS XS1-XAU8A-10's ARM core config - * XMOS xCORE-XA Core Module board config - * Exynos5250 target config - * Arndale board config - * FM4 MB9BFxxx family configs - * Spansion SK-FM4-U120-9B560 board config - * Diolan LPC4357-DB1 board config - * ST STM32F469 discovery board config - * ST STM32F7-DISCO, STM327[4|5]6G-EVAL boards configs - * ST STM32L4 discovery, NUCLEO L476RG, STM32F429I-DISC1 boards - configs - * Atheros AR2313, AR2315 targets config - * Netgear WP102 board config - * La Fonera FON2200 board config - * Linksys WAG200G board config - * LPC-Link2 board config - * NXP LPC4370 target config - * Atmel SAMV, SAMS, SAME target configs - * Atmel SAM E70 Xplained, SAM V71 Xplained Ultra boards - configs - * Nordic nRF52 target config - * Nordic nRF51-DK, nRF52-DK boards configs - * Infineon XMC4700 Relax Kit, XMC4800 Relax EtherCAT Kit, - XMC4300 Relax EtherCAT Kit boards configs - * Renesas S7G2 target config - * Renesas DK-S7G2 board config - * Altera EP3C10 FPGA (Cyclone III family) target config - * TI MSP432P4xx target config - * Cypress PSoC 5LP target config - * Analog Devices ADSP-SC58x target config (Cortex-A5 core only) Server Layer: - * tcl_trace command for async target trace output via Tcl RPC Documentation: Build and Release: - * Various fixes thanks to http://coccinellery.org/ - * libftdi is now autodetected with pkgconfig - * Releases should now support reproducible builds - * Conversion to non-recursive make, requires automake >= 1.14 - * Udev rules modified to add uaccess tag and moved to - 60-openocd.rules - * Support searching for scripts relative to the openocd binary - for all major architectures This release also contains a number of other important functional and cosmetic bugfixes. For more details about what has changed since the last release, see the git repository history: -http://sourceforge.net/p/openocd/code/ci/v0.10.0/log/?path= +http://sourceforge.net/p/openocd/code/ci/v0.x.0/log/?path= For older NEWS, see the NEWS files associated with each release diff --git a/NEWS-0.10.0 b/NEWS-0.10.0 new file mode 100644 index 000000000..e3b1e2565 --- /dev/null +++ b/NEWS-0.10.0 @@ -0,0 +1,155 @@ +This file includes highlights of the changes made in the OpenOCD +source archive release. + +JTAG Layer: + * New driver for J-Link adapters based on libjaylink + (including support for FPGA configuration, SWO and EMUCOM) + * FTDI improvements to work at 30MHz clock + * BCM2835 native driver SWD and Raspberry Pi2 support + * BCM2835 is set to 4ma drive, slow slew rate + * ixo-usb-jtag (emulation of an Altera Bus Blaster I on + Cypress FX2 IC) support + * JTAG pass-through mode for CMSIS-DAP (including support for + FPGA configuration) + * OpenJTAG support for Cypress CY7C65215 + * connect_assert_srst support for SWD + * Xilinx Virtex-II Series7 bitstream loading support + * Use JEP106 data to decode IDs + * Deprecated "ft2232" driver removed (use "ftdi" instead) + * GPL-incompatible FTDI D2XX library support dropped (Presto, + OpenJTAG and USB-Blaster I are using libftdi only now) + * ZY1000 support dropped (unmaintained since long) + * oocd_trace support dropped + +Boundary Scan: + +Target Layer: + * ARMv7-A, Cortex-M, Cortex-A/R important fixes and + improvements (allowing e.g. simultaneous debugging of A8 and + M3 cores, JTAG WAIT support etc.) + * ARM Cortex-A,R allow interrupt disable during single-step + (maskisr command) + * Semihosting support for ARMv7-A + * ARM Cortex-M7 support + * Intel Quark mcu D2000 support + * Freescale LS102x SAP support + * ThreadX RTOS support on ARM926E-JS + * Cortex-M RTOS stack alignment fixes + * FreeRTOS FPU support + * uC/OS-III RTOS support + * bridging semihosting to GDB's File-I/O support + * -defer-examine option added to target create command + * verify_image_checksum command added + +Flash Layer: + * Atmel SAM4S, SAM4N, SAM4C support + * Atmel SAMV, SAMS, SAME (Cortex-M7) support + * Atmel AT91SAMD handle reset run/halt in DSU, other fixes + * Atmel AT91SAML21, SAML22, SAMC20/SAMC21, SAMD09 support + * ST STM32F4x support + * ST STM32F74x/76x/77x, STM32L4 support + * ST STM32L0 categories 1, 2 and 5 support + * Kinetis K02, K21, K22, K24, K26, K63, K64, K66 support + * Kinetis KE, KVx, K8x families support + * Kinetis FlexNVM handling + * Kinetis flash protection, security, mass_erase improvements + * Infineon XMC4xxx family support + * Infineon XMC1000 flash driver + * Energy Micro EFM32 Happy Gecko support + * Energy Micro EFM32 debug interface lock support + * Analog Devices ADuCM360 support + * Unified Nuvoton NuMicro flash driver + * NIIET K1921VK01T (Cortex-M4) support + * Nordic Semiconductor nRF51 improvements + * Spansion FM4 flash (including MB9BFx64/x65, S6E2DH) driver + * Ambiq Micro Apollo flash driver + * PIC32MX new device IDs, 17x/27x flash support + * read_bank() and verify_bank() NOR flash internal API to + allow reading (and verifying) non-memory-mapped devices + * JTAGSPI driver to access SPI NOR flashes via a trivial + FPGA proxy + * Milandr read/verify for Info memory support + * Various discrete SPI NOR flashes support + * CFI 16-bit flash reversed endianness support + +Board, Target, and Interface Configuration Scripts: + * Digilent JTAG-HS2, JTAG-HS3 interfaces configs + * FTDI UM232H module as JTAG interface config + * 100ask's OpenJTAG interface config + * MBFTDI interface config + * XDS100v3 interface config + * Freescale Vybrid VF6xx target config + * EmCraft VF6 SOM and baseboard configs + * Freescale SabreSD board config + * Freescale VF65GS10 tower board config + * Pipistrello Xilinx Spartan6 LX45 FPGA board config + * miniSpartan6+ board config + * Xilinx Kintex7 Development board config + * Parallella-I board config + * Digilent Atlys and Analog Discovery board configs + * Numato Opsis board config + * Xilinx Spartan 6 FPGA "Device DNA" reading support + * Altera 10M50 FPGA (MAX10 family) target config + * Altera EPM240 CPLD (MAXII family) target config + * Marsohod2, Marsohod3 FPGA, Marsohod CPLD boards configs + * Novena's integrated FPGA board config + * XMOS XS1-XAU8A-10's ARM core config + * XMOS xCORE-XA Core Module board config + * Exynos5250 target config + * Arndale board config + * FM4 MB9BFxxx family configs + * Spansion SK-FM4-U120-9B560 board config + * Diolan LPC4357-DB1 board config + * ST STM32F469 discovery board config + * ST STM32F7-DISCO, STM327[4|5]6G-EVAL boards configs + * ST STM32L4 discovery, NUCLEO L476RG, STM32F429I-DISC1 boards + configs + * Atheros AR2313, AR2315 targets config + * Netgear WP102 board config + * La Fonera FON2200 board config + * Linksys WAG200G board config + * LPC-Link2 board config + * NXP LPC4370 target config + * Atmel SAMV, SAMS, SAME target configs + * Atmel SAM E70 Xplained, SAM V71 Xplained Ultra boards + configs + * Nordic nRF52 target config + * Nordic nRF51-DK, nRF52-DK boards configs + * Infineon XMC4700 Relax Kit, XMC4800 Relax EtherCAT Kit, + XMC4300 Relax EtherCAT Kit boards configs + * Renesas S7G2 target config + * Renesas DK-S7G2 board config + * Altera EP3C10 FPGA (Cyclone III family) target config + * TI MSP432P4xx target config + * Cypress PSoC 5LP target config + * Analog Devices ADSP-SC58x target config (Cortex-A5 core only) + +Server Layer: + * tcl_trace command for async target trace output via Tcl RPC + +Documentation: + +Build and Release: + * Various fixes thanks to http://coccinellery.org/ + * libftdi is now autodetected with pkgconfig + * Releases should now support reproducible builds + * Conversion to non-recursive make, requires automake >= 1.14 + * Udev rules modified to add uaccess tag and moved to + 60-openocd.rules + * Support searching for scripts relative to the openocd binary + for all major architectures + + +This release also contains a number of other important functional and +cosmetic bugfixes. For more details about what has changed since the +last release, see the git repository history: + +http://sourceforge.net/p/openocd/code/ci/v0.10.0/log/?path= + + +For older NEWS, see the NEWS files associated with each release +(i.e. NEWS-<version>). + +For more information about contributing test reports, bug fixes, or new +features and device support, please read the new Developer Manual (or +the BUGS and PATCHES.txt files in the source archive). diff --git a/configure.ac b/configure.ac index 6949402a3..2543eca3a 100644 --- a/configure.ac +++ b/configure.ac @@ -1,5 +1,5 @@ AC_PREREQ(2.64) -AC_INIT([openocd], [0.10.0], +AC_INIT([openocd], [0.10.0+dev], [OpenOCD Mailing List <openocd-devel@lists.sourceforge.net>]) AC_CONFIG_SRCDIR([src/openocd.c]) -- GitLab